<button id="bbofb"><acronym id="bbofb"></acronym></button>

      <form id="bbofb"><wbr id="bbofb"><kbd id="bbofb"></kbd></wbr></form>

      1. <rp id="bbofb"></rp>
      2. <dd id="bbofb"><pre id="bbofb"></pre></dd>

        老化測試設備

        咨詢熱線

        18566398802
        首頁 > 標準大全 > ASTM D470-2013標準詳情
        相關測試儀器

        ASTM D470-2013測試標準

          本頁面標準信息均來源于網絡收集,或由參與標準制定的供應商提供,只作為參考使用。我們愿意和您交流ASTM D470-2013標準細節信息或ASTM D470-2013測試方法,歡迎致電【18566398802】

        ASTM D470-2013標準介紹

        ASTM D470-13是關于《電線和電纜用交聯絕緣材料與套管的標準試驗方法 》現行版本標準修訂于2013年,替代原ASTM D470-99版本使用。

        1. Scope

        1.1 These test methods cover procedures for testing crosslinked insulations and jackets for wire and cable. To determine the test to be made on the particular insulation or jacket, refer to the product specification for that type. These test methods do not apply to the class of products known as flexible cords.

        1.2 In many instances the insulation or jacket cannot be tested unless it has been formed around a conductor or cable. Therefore, tests are done on insulated or jacketed wire or cable in these test methods solely to determine the relevant property of the insulation or jacket and not to test the conductor or completed cable.

        1.3 The procedures appear in the following sections:

        Sections

        AC and DC Voltage Withstand Tests22 to 29

        Capacitance and Dissipation Factor Tests38 to 44

        Cold Bend128

        Cold Bend, Long-Time Voltage Test on Short Specimens51 to 57

        Double AC Voltage Test on Short Specimens 45 to 50

        Electrical Tests of Insulation17 to 64

        Heat Distortion Test127

        Horizontal Flame Test100 to 104

        Insulation Resistance Tests on Completed Cable30 to 37

        Mineral Filler Content, Determination of111 to 115

        Ozone Resistance Test87 to 99

        Partial-Discharge Test58 to 64

        Physical Tests of Insulation and Jacket Compounds 5 to 16

        Surface Resistivity Test116 to 120

        Track Resistance Test129 to 132

        U-Bend Discharge Test121 to 125

        Water Absorption Test65 to 71

        Water Absorption Test, Accelerated72 to 86

        Water Absorption Test on Fibrous Coverings 105 to 110

        1.4 Whenever two sets of values are presented, in different units, the values in the first set are the standard, while those in the parentheses are for information only.

        1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazards see Section 4.

        2. Referenced Documents

        ASTM Standards

        D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies

        D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation

        D257 Test Methods for DC Resistance or Conductance of Insulating Materials

        D412 Test Methods for Vulcanized Rubber and Thermoplastic ElastomersTension

        D454 Test Method for Rubber Deterioration by Heat and Air Pressure

        D572 Test Method for RubberDeterioration by Heat and Oxygen

        D573 Test Method for RubberDeterioration in an Air Oven

        D1193 Specification for Reagent Water

        D1711 Terminology Relating to Electrical Insulation

        D2132 Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials

        D3755 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Under Direct-Voltage Stress

        D5025 Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials

        D5207 Practice for Confirmation of 20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning Tests on Plastic Materials

        D5423 Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation

        溫馨提醒:本ASTM D470-2013可能存在更新的版本,建議尋找ASTM D470-2013的發行商確認。

        符合 ASTM D470-2013 標準的
        老化試驗箱

        近期文章
        亚洲av无码不卡免费在线观看

            <button id="bbofb"><acronym id="bbofb"></acronym></button>

            <form id="bbofb"><wbr id="bbofb"><kbd id="bbofb"></kbd></wbr></form>

            1. <rp id="bbofb"></rp>
            2. <dd id="bbofb"><pre id="bbofb"></pre></dd>