<button id="bbofb"><acronym id="bbofb"></acronym></button>

      <form id="bbofb"><wbr id="bbofb"><kbd id="bbofb"></kbd></wbr></form>

      1. <rp id="bbofb"></rp>
      2. <dd id="bbofb"><pre id="bbofb"></pre></dd>

        老化測試設備

        咨詢熱線

        18566398802
        首頁 > 標準大全 > ASTM D1149-07標準詳情
        相關測試儀器

        ASTM D1149-07測試標準

        (該標準已經被ASTM D1149 - 16替代)
          本頁面標準信息均來源于網絡收集,或由參與標準制定的供應商提供,只作為參考使用。我們愿意和您交流ASTM D1149-07標準細節信息或ASTM D1149-07測試方法,歡迎致電【18566398802】

        ASTM D1149-07標準介紹

        ASTM D1149-07簡介

        ASTM D1149是關于橡膠暴露在一定的程度的含氧環境下,靜態或者動態表面拉伸情況下的性能變化的標準,標準后續所帶的數字為標準最新修改被采用的年份。出于版權保護原因,本文僅摘抄部分ASTM D1149-07英文標準,如需完整ASTM D1149-07內容請購買請垂詢客服人員。

        ASTM D1149-07英文原版摘抄

        1. Scope

        1.1 These test methods are used to estimate the effect of exposure, under surface tensile strain conditions, either dynamic or static, in an atmosphere containing specified levels of ozone concentration, expressed as partial pressure (refer to Note 1), on vulcanized rubber, rubber compounds, molded or extruded soft rubber, and other specified materials, or as may be determined empirically. The effect of naturally occurring sunlight or light from artificial sources is excluded.

        1.2 Previously published ASTM documents Test Method D 518 and Test Methods D 3395 have been included in these test methods, D 1149, in 2007. Please refer to Note 2.

        1.2.1 Test Method D 518 and Test Methods D 3395 have henceforth been withdrawn and superseded by Test Methods D 1149. When Test Methods D 1149 is cited, or otherwise referenced, a notation shall be included to this effect. Please refer to section for the appropriate references.

        1.3 The specified conditions of exposure to ozone in the controlled environments are accelerated in comparison to outdoor exposure. These accelerated ozone test methods may not give results which correlate with outdoor exposure tests or service performance.

        1.4 All materials, instruments, or equipment used for the determination of mass, force, dimension, ozone concentration, partial pressure, temperature, velocity, and gas exchange rate shall have direct traceability to the National Institute for Standards and Technology, or other internationally recognized organization parallel in nature.

        1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only. Many of the stated SI units are direct conversions from the U.S. Customary System to accommodate the instrumentation, practices, and procedures that existed prior to the Metric Conversion Act of 1975.

        This standard involves hazardous materials, specifically ozone. It may also involve hazardous operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

        Note 1

        A discussion and explanation regarding the measurement of ozone concentrations based upon parts of ozone per unit of air versus partial pressure is provided in Test Methods D 4575, specifically Appendices X1 and X2. Test Methods D 4575 is also recommended as a source of background information regarding standards involving materials exposed to ozone.

        2. Referenced Documents

        ASTM Standards

        D518 Test Method for Rubber Deterioration--Surface Cracking

        D1171 Test Method for Rubber DeteriorationSurface Ozone Cracking Outdoors (Triangular Specimens)

        D1349 Practice for Rubber--Standard Conditions for Testing

        D3182 Practice for RubberMaterials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets

        D3395 Test Methods for Rubber Deterioration--Dynamic Ozone Cracking in a Chamber

        D4482 Test Method for Rubber Property--Extension Cycling Fatigue

        D4575 Test Methods for Rubber DeteriorationReference and Alternative Method(s) for Determining Ozone Level in Laboratory Test Chambers

        溫馨提醒:本ASTM D1149-07可能存在更新的版本,建議尋找ASTM D1149-07的發行商確認。

        符合 ASTM D1149-07 標準的
        老化試驗箱

        近期文章
        亚洲av无码不卡免费在线观看

            <button id="bbofb"><acronym id="bbofb"></acronym></button>

            <form id="bbofb"><wbr id="bbofb"><kbd id="bbofb"></kbd></wbr></form>

            1. <rp id="bbofb"></rp>
            2. <dd id="bbofb"><pre id="bbofb"></pre></dd>