<button id="bbofb"><acronym id="bbofb"></acronym></button>

      <form id="bbofb"><wbr id="bbofb"><kbd id="bbofb"></kbd></wbr></form>

      1. <rp id="bbofb"></rp>
      2. <dd id="bbofb"><pre id="bbofb"></pre></dd>



        首頁 > 標準大全 > ASTM D4303-2016標準詳情

        ASTM D4303-2016測試標準

          本頁面標準信息均來源于網絡收集,或由參與標準制定的供應商提供,只作為參考使用。我們愿意和您交流ASTM D4303-2016標準細節信息或ASTM D4303-2016測試方法,歡迎致電【18566398802】

        ASTM D4303-2016標準介紹







        Q-sun氙燈試驗箱ASTM D4303測試方法

        ASTM D4303測試方法

        ASTM D4303英文版本(節選)

        Significance and Use

        The retention of chromatic properties by a colorant over a long period of years is essential in a work of art. Accelerated exposure simulates color changes that may reasonably be expected. The producer and the user of artists' materials, therefore, can be apprised of suitable colorants.

        Variations in results may be expected between the test methods. Also, some variation may be expected when the same test is repeated. Variations in Methods A and B are due to differences in outdoor conditions that are not accounted for in testing to equivalent radiant exposures. Information on sources of variability and strategies for addressing variability in laboratory accelerated exposure tests is found in Guide G141.

        This standard does not cover factors other than lightfastness that can affect the permanence of art materials.

        1. Scope

        1.1 Four test methods to accelerate the effects of long term indoor illumination on artists' materials are described below. One of the natural daylight methods and one of the xenon-arc methods are used to categorize the lightfastness of colorants.

        1.1.1 Test Method A—Exposure in southern Florida to natural daylight filtered through window glass.

        1.1.2 Test Method B—Exposure in Arizona to natural daylight filtered through window glass.

        1.1.3 Test Method C—Exposure in a non-humidity controlled xenon-arc device simulating daylight filtered through window glass.

        1.1.4 Test Method D—Exposure in a humidity controlled xenon-arc device simulating daylight filtered through window glass.

        1.2 These test methods are used to approximate the color change that can be expected over time in colorants used in artists' materials exposed indoors to daylight through window glass.

        Note 1—The color changes that result from accelerated exposure may not duplicate the results of normal indoor exposure in a home, art gallery, or museum. The relative resistance to change, however, can be established so colored materials can be assigned to categories of relative lightfastness.

        Note 2—Users who wish to test colored materials under fluorescent illumination should consult Practice D4674.

        1.3 Lightfastness categories are established to which colorants are assigned based on the color difference between specimens before and after exposure.

        1.4 Color difference units are calculated by the CIE 1976 L*a*b* color difference equation.

        1.5 These test methods apply to colored artists' materials.

        1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

        1.7 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

        2. Referenced Documents

        ASTM Standards

        D2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color Coordinates

        D4302 Specification for Artists Oil, Resin-Oil, and Alkyd Paints

        D4674 Practice for Accelerated Testing for Color Stability of Plastics Exposed to Indoor Office Environments

        D5067 Specification for Artists Watercolor Paints

        D5098 Specification for Artists Acrylic Dispersion Paints

        D5724 Specification for Gouache Paints

        D6901 Specification for Artists Colored Pencils

        E284 Terminology of Appearance

        E1347 Test Method for Color and Color-Difference Measurement by Tristimulus Colorimetry

        E1348 Test Method for Transmittance and Color by Spectrophotometry Using Hemispherical Geometry

        E1349 Test Method for Reflectance Factor and Color by Spectrophotometry Using Bidirectional (45:0 or 0:45) Geometry

        G24 Practice for Conducting Exposures to Daylight Filtered Through Glass

        G113 Terminology Relating to Natural and Artificial Weathering Tests of Nonmetallic Materials

        G141 Guide for Addressing Variability in Exposure Testing of Nonmetallic Materials

        G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources

        G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials

        溫馨提醒:本ASTM D4303-2016可能存在更新的版本,建議尋找ASTM D4303-2016的發行商確認。

        符合 ASTM D4303-2016 標準的

        • 氙燈加速老化試驗箱圖片 氙燈加速老化試驗箱

          Q-sun Xe-1-BCE氙燈加速老化試驗箱配有全光譜氙弧燈、太陽眼輻照度控制系統,該型號的氙燈加速老化試驗箱同時具有背部噴功能。

          Q-sun Xe-1-BCE 馬上詢價
        • 氙燈老化試驗機圖片 氙燈老化試驗機

          Q-SUN Xe-3-HCE是一款具有全光譜光照模擬、濕度控制以及制冷功能的氙燈老化試驗機,其命名規則為濕度控制(H)、制冷功能(C)。

          Q-SUN Xe-3-HCE 馬上詢價

            <button id="bbofb"><acronym id="bbofb"></acronym></button>

            <form id="bbofb"><wbr id="bbofb"><kbd id="bbofb"></kbd></wbr></form>

            1. <rp id="bbofb"></rp>
            2. <dd id="bbofb"><pre id="bbofb"></pre></dd>